CqKds/hqdefault.jpg' alt='Chain Link Fence Uneven Ground Installations' title='Chain Link Fence Uneven Ground Installations' />Work Method Statement for Painting Work Buildings CIVIL TRAINING FOR YOUNG ENGINEERSWORK METHOD STATEMENT FOR PAINTING WORK BUILDINGSTABLE OF CONTENTS1       PURPOSE2       SCOPE3       STEP OF WORKS4       JOB SAFETY ANALYSIS 5       QAQC INSPECTION6       ATTACHMENT            ATTACHMENT 1 PRODUCT DATA SHEETS            ATTACHMENT 2 MATERIAL SAFETY AND DATA SHEETS MSDS1. PURPOSEThe purpose of this Work Method Statement for Painting of Building is to outline and describe in detail the procedure to be adopted such as type of paint and recommended surface preparation, in which to ensure our compliance with the Safety Requirements Procedure and project specifications. Inform all concerned supervisor including workers the value and importance of this activity prior to implementation in any Project. SCOPEThe scope of this Method Statement covers the works in any Project Building and Substation including buildings in existing plant as follows          Painting Works for Exterior Walls, Interior Walls, Concrete Floor, Exposed CeilingSlab Soffit, Cable Room and Below Raised Floor. STEP OF WORKS3. 1 Surface Preparation     Surfaces are to be prepared in accordance with good painting practices and in accordance with the technical product information sheets of the painting products. Painting must not take place where the surface are moist or greasy or may become so before application of the first coat of paint primer. Painting must not take place when the surface temperature is less than 3C above surrounding airs dew point, when the air relative humidity is higher than 8. C.     Prior to any application, the surface must be stable, firm, dry and free of dust and concrete laitance. Sketchup 5 Free Download Crack Idm more. The surface must have no cracks. Scaffolding and work at heights. Please refer to WMS for Scaffolding Installation. Preparation of Coating Materials    All coating materials shall be thoroughly stirred in a container. Only approved thinners shall be used. Mixing shall be carried out in a well ventilated area. Mighty Mule 10 Watt Solar Gate Battery Charger Works with All Mighty Mule Gate Openers, Model FM123. Refer to Product Data and Specification Sheet for Mixing Ratio. During Mixing and Painting Application, appropriate mask shall be worn in accordance with the recommendation of approved MSDS. MSDS shall be available at site and made known to workers. Coating    Each coat shall be applied uniformly over the entire surface. Any uneven surface shall be rectified by filling up using approved Acrylic Filler, then apply sanding when dry and apply recoat. On beams, columns and irregular surfaces, edges shall be coated first and an extra pass made later. Each coat shall be allowed to dry for the time specified by approved before application of any succeeding coat. Refer to Product Data and Specification also to check Applicable Rate and Dry Film Thickness DFT. Any primer coat exposed to excess humidity or rain before drying shall be permitted to dry and the damaged area of primer should be removed to the bare substrate. Dust and loose particle shall be removed by sanding until the surface is dry, sound and cleaned. Re apply using the same primer and when dry apply paint filler to check for flat and smooth surfaces. When the surface is ready to receive topcoat then applied the required coating to meet DFT and specifications. The time interval between applications of two 2 successive coats must not exceed that specified by product. Any coating shall be cleaned and free of spray dust before the next coat is applied. Coatings shall be continuous that means free of pin holes, voids, bubbles and other defects. Where application is to be carried out by brush, brushes shall be of a type and quality as well as for using roller which permit proper application of the material. For spray application, spray guns, hoses and pumps shall be cleaned before new material is added. An adequate moisture trap shall be installed between the air supply and each application unit. Specified film thickness for coating material shall be strictly observed. Dry film thickness shall be checked with appropriate film thickness gauges. Before application of final coat, all damaged areas shall be properly repaired using the original paint system. Apply Acrylic Protective Paint for exterior wall and use Acrylic Emulsion Resin for interior wall. JOB SAFETY ANALYSISJSA RA5. QAQC INSPECTIONRefer wms Painting Works. ATTACHMENT   Product Data Sheets Material Safety and Data Sheets MSDS. Archives Philly. A husband and wife purchased our DIY dog fence kit and installed 900 linear feet of fencing on their rocky uneven Colorado land for their 2 awesome dogs. Heres a. Wire Mounting Height. How high above the ground should you mount the dog fence boundary wire The ideal height for the dog fence wire is the height of the dogs neck. Find the latest business news on Wall Street, jobs and the economy, the housing market, personal finance and money investments and much more on ABC News. Dear customer, This year GEA Farm Technologies will be offering its agricultural supplies catalogue for the first time in cooperation with the Kerbl Group. No matter how you slice it, keeping some extra battery power on your person can do wonders to affect how you move through the world. If youd like to take some.